Back to Blog
Tips & Care 2026-11-14 Excel Blades: Precision Cutting Tools & Craft Knives 4 views

Why Your #55 Drill Bits Keep Breaking and How to Prevent It

Why Your #55 Drill Bits Keep Breaking and How to Prevent It

A #55 drill bit snaps when the setup, not the bit, is wrong. Learn what the Excel Blades #55 set actually gives you and how to drill tiny holes without breakage.

The break usually starts before the bit touches the material

A snapped #55 bit is rarely a defective bit. At 0.0520 inches (1.32 mm) in diameter, the drill has very little material to absorb side load, so any wobble, misalignment, or forcing shows up as a break. Before you blame the bit, check three things: whether the bit is held straight and secure, whether the tool handle is compatible, and whether the material and feed pressure match a bit this small.

The Excel Blades Drill Bits #55 set gives you twelve identical bits in a plastic storage tube. That redundancy is useful for diagnosis: if one bit breaks and the next one drills cleanly in the same setup, the problem was likely that bit or its installation. If every bit breaks in the same spot, the setup needs attention.

What the #55 set actually gives you

  • Drills #55: Includes twelve precision #55 high-speed steel twist drill bits, each 0.0520 inches (1.32 mm) in diameter. Twelve identical bits let you replace a broken one without changing your hole size, and the consistent diameter makes setup errors easier to spot.
    Drills #55
    Drills #55
  • Drills #55: Compatible with Excel tool models 70003, 70005, 70011, 70023, and 55661. Using a compatible handle is the first defense against wobble; an ill-fitting chuck or collet can let the bit shift and snap.
  • Drills #55: The bits are stored in a durable plastic tube. Loose bits in a drawer can nick edges or bend shanks; the tube protects the cutting edges and keeps the set organized between projects.

Check these four points before your next hole

Work through these in order. Each one addresses a common source of side load on a small bit, and each is something you can verify with the supplied product information.

  • Handle compatibility: Confirm your handle is one of the listed Excel models. If it is not, the bit may not seat concentrically, which introduces runout and bending force.
  • Bit seating: Insert the bit fully into the chuck or collet and tighten evenly. A bit that slips or sits at an angle will break far more easily than a straight, secure one.
  • Material match: The #55 set is listed for wood, resin, jewelry, walnut, amber, beeswax, olive nut, beads, PVC, acrylic, and plastics. If you are drilling something outside that list, the bit may not be the right choice, and breakage is a signal to reconsider.
  • Feed pressure: Let the bit cut. Pushing hard on a 1.32 mm drill adds heat and side load. The supplied record does not include a recommended feed rate, so use light, steady pressure and clear chips often.

Why the same bit breaks in the same place

If you keep snapping bits at the same point in a project, the cause is usually geometric. A hole started at an angle, a bit that deflects as it enters, or a workpiece that shifts mid-drill all concentrate stress at one spot. The fix is to stabilize the work and start the hole perpendicular. A center mark or a pilot dimple gives the point something to bite, reducing the chance of the bit skating and then snapping when it finally catches.

The supplied information does not include a recommended drilling speed or pressure for the #55 set, so avoid treating any single number as a manufacturer instruction. Instead, watch the chips: fine, continuous curls mean the bit is cutting; dust or heat means it is rubbing.

Storage and handling between sessions

The plastic tube is not just packaging. Bits this small can be damaged by contact with other tools, and a bent shank will never drill straight. Return each bit to the tube after use, and avoid dropping the tube. If a bit does take a fall, inspect it before the next hole: a visible bend or a dulled edge is a reason to swap in a fresh bit from the set rather than risk a break mid-project.

When to replace rather than persist

A bit that has already snapped once is not repairable. Because the set includes twelve, you can retire a damaged bit without losing the ability to drill the same size hole. Keep the broken bit out of the tube so you do not confuse it with a good one, and note what you were doing when it broke. That note is the most useful diagnostic tool you have: it tells you whether the problem is a specific material, a specific handle, or a specific step in your routine.

What this means for your next project

Most #55 breakage comes down to a setup that allows movement. Start with a compatible handle, seat the bit straight, stabilize the workpiece, and use light pressure. If a bit still breaks, compare the circumstances with the previous break; the pattern will point to the fix. The Excel Blades Drill Bits #55 set gives you enough bits to test changes without stopping your project, and the storage tube helps keep the spares in good condition.

Related Articles

Customer Service
Home
Products
Cart
Profile