Back to Blog
How-to Guides 2026-11-02 Excel Blades: Precision Cutting Tools & Craft Knives 0 views

Double Ended Pin Vise Drill: How to Hold Tiny Bits Steady

Double Ended Pin Vise Drill: How to Hold Tiny Bits Steady

Learn how to load, grip, and drill with a double ended pin vise so small bits stay steady. Step-by-step checks for jewelry, models, and craft drilling.

Quick answer

Load the bit into the collet that matches its shank, tighten both ends firmly, and hold the tool vertically with a light, high-speed twist. Check that the bit runs true before touching the workpiece.

Why two collets change how you load the tool

A double-ended pin vise has a collet at each end, so you can keep two bit sizes ready or switch tasks without hunting for a second tool. The trade-off is that the unused end still holds a bit, which can catch on sleeves or scratch a finished surface if you lay the tool down carelessly.

Treat each end as its own setup: match the collet to the bit shank, tighten it fully, and cap or retract the other end when it is not in use. If a collet feels loose even when closed, stop and check that the bit shank is the right size rather than forcing it.

Chuck size limits you should check before drilling

Pin vise chuck sizes vary, and a collet only grips securely within its intended range. A bit that is too small may spin instead of cutting; one that is too large will not seat. Because the catalog does not list a specific collet range for this tool, test-fit your bit by hand before tightening and confirm it sits centered, not angled.

For jewelry making and model work, the practical rule is to use the largest bit that fits the hole you need and the smallest collet that accepts that bit. This reduces runout and gives you more control on thin sheet or soft metal.

When a pin vise is the wrong tool

A pin vise is a hand tool, so it suits small holes in wood, plastic, soft metal, and resin where you can control pressure by feel. It is not a substitute for a drill press or a rotary tool when you need many identical holes, deep bores, or hard steel. In those cases, use the pin vise for layout and starting marks, then switch to a powered tool if the material allows.

Step-by-step: loading and drilling with a double ended pin vise

  1. Match the bit to the collet: Open one collet and insert the bit shank until it seats fully. Close the collet by hand, then tighten firmly. Common mistake: inserting the bit at an angle or only partway, which causes wobble. The bit should sit centered and deep enough that the flutes are clear of the collet.
  2. Check runout before drilling: Hold the tool horizontally and spin it slowly against a light background. Watch the tip for a circle rather than a point. If it wobbles, loosen, reseat, and tighten again. A bit that still wobbles after reseating is likely the wrong shank size for that collet.
  3. Mark and center your hole: Use a scribe or awl to make a small dimple at the drilling point. Place the bit tip in the dimple and hold the pin vise vertical to the surface. Common mistake: starting on a flat surface without a mark, which lets the bit wander. A dimple is especially important on curved or polished jewelry surfaces.
  4. Drill with light pressure and steady rotation: Turn the pin vise clockwise in short, even twists while keeping light downward pressure. Clear chips every few turns by withdrawing the bit. Common mistake: pressing hard and spinning fast, which snaps small bits. Let the bit cut; if you feel heat or resistance, back out and clear the hole.
  5. Secure the unused end: When the second collet holds another bit, point it away from the work and keep it capped or retracted when not in use. Common mistake: leaving a sharp bit exposed where it can scratch the workpiece or your hand. Store the tool with both ends closed or capped to protect the collets and bits.

Product facts

  • Double Ended Pin Vise Drill: The Excel Blades 4" Double Ended Pin Vise has two adjustable collets for holding micro drill bits, wire, and small tools. Two collets let you keep a drill bit in one end and a wire or reamer in the other, so you can switch tasks without re-chucking.
    Double Ended Pin Vise Drill
    Double Ended Pin Vise Drill

Related Articles

Customer Service
Home
Products
Cart
Profile